Home »
Video Splitters »
Low-Cost HDMI Over Gigabit IP Network Range Extender

ST-IPHD-LC

Low-Cost HDMI Over Gigabit IP Network Range Extender

NTI Part #: ST-IPHD-LC-Group

Also known as: HDMI over IP network extender, media center extender CAT6, remote digital HDMI monitor display, HDMI transmitter/receiver, HDMI range extender, high definition 1080p extender, extend HDTV video, gigabit HDMI extender

Product Highlights

Extend 1080p video up to 330 ft via One CATx Cable
Supports Point-to-Point, Point-to-Many, & Many-to-Many connections

ROHS Compliant Low-Cost HDMI Over Gigabit IP Network Range Extender
Low-Cost HDMI Over Gigabit IP Network Range ExtenderDigital Signage Product
CE Compliant Low-Cost HDMI Over Gigabit IP Network Range Extender
FCC Compliant Low-Cost HDMI Over Gigabit IP Network Range Extender

Scroll Down to Get Quote

The XTENDEX® Low-Cost HDMI Over Gigabit IP Extender multicasts digital video and audio signals to one or more receivers up to 330 feet away over a 1000Base-T Gigabit Network connected with CAT5e/6 cable.

Each Low-Cost HDMI Over Gigabit IP Extender consists of a local unit that connects to an HDMI source, and a remote unit that connects to an HDMI display. The local and remote units can be connected together for a Point-to-Point connection via CATx or a Point-to-Many connection via a network switch. Support for multiple transmitters requires a managed network switch.

Supports HDTV resolutions to 1080p.
Ideal solution for digital signage applications.
Broadcast real-time HDMI video and audio signals to multiple display locations with a managed or unmanaged (also known as non-managed) network switch.
Transmits an HDMI signal over one CAT5e/6 cable.
Plug-and-Play installation allows receivers to find the transmitters automatically on the same subnet. (Network configuration may be required for managed network switch.)
Web interface for changing IP addresses, firmware updates and resetting units to factory default settings.
Easily expandable. Add remote units as you add monitors.
Inexpensive CAT5e/6 cable replaces bulky video cables.
Supports 10/100/1000 Ethernet connection.
Built in default EDID table.
HDCP compliant.
Support for multiple transmitters requires a managed network switch with VLAN/IGMP support. Standard LAN switches can only support one transmitter.
- The managed switch must support port based IEEE 802.1Q VLAN, IGMP, and permit duplicate IP addresses across the VLAN domains.
- Each VLAN acts as a separate HDMI Over IP Channel on the network.
- Number of local and remote units that can be used is dependent on the backplane bandwidth of the switch.
- Cascade manage switches up to 3 levels, allowing the farthest display to be located up to 1,000 feet away from the source device. Each receiver can be located up to 330 feet away.
For a point-to-many connection, a standalone network with an unmanaged network switch, hub, or router can be used instead of a managed network switch.
- It is not recommended to use any other network devices on this standalone network as it may cause a degradation in performance.
Uses M-JPEG technology to process image compression on a fixed bandwidth.
- Note: at high resolutions, characters on PCs get noticeably fuzzy due to image compression and decompression process.
Local and remote units must be in the same LAN. The units do not support WAN connections.

Local Unit

One female HDMI-A port for source connection.
One female 1000Mbps RJ45 port for sending high definition video/audio signals.
Supported input resolutions: 480i@60Hz, 480p@60Hz, 576i@50Hz, 576p@50Hz, 720p@50/60Hz, 1080i@50/60Hz, 1080p@50/60Hz
Max. bit rate: 80 Mbps.
Codec: MJPEG
Encoding delay: 33 mS at 30fps latency

Remote Unit

One female HDMI-A port for HDTV or computer display.
One female 1000Mbps RJ45 port for receiving high definition video/audio signals.
Supported output resolutions: 480p@60Hz, 576p@50Hz, 720p@50/60Hz, 1080p@50/60Hz
Supports embedded digital audio through HDMI compatible TVs or audio receivers.

Power

Local and remote unit: 110 or 240 VAC at 50 or 60 Hz via AC adapter.
- Power Cord Plug
  - ST-IPHD-LC: US NEMA 1-15P
  - ST-IPHD-LCEU: Europlug CEE 7/16
  - ST-IPHD-LCUK: UK BS1363
  - ST-IPHD-LCAU: AS/NZS 3112
  - ST-IPHD-LCUNV: US NEMA 1-15P with country-specific universal power plug adapter
Power consumption: 3W each.

Max Distance

330 feet (100 meters) over CAT5e/6 cable.

Cables

Use HD-xx-MM cable to connect an HDMI source or display (not included).
Use DVI-HD-xx-MM cable to connect a DVI source or display (not included).
Use CAT5e/6 solid or stranded straight through cable for TIA/EIA-568B wiring terminated with standard RJ45 connectors (not included).

Environmental

Operating and storage temperature: 14 to 140°F (-10 to 60°C).
Operating and storage relative humidity: 20 to 90% non-condensing RH.

Dimensions

WxDxH: 2.28x4.33x1.02 in (58x110x26 mm)

Regulatory Approvals

CE, FCC, RoHS

Warranty

Two years.

Compatible NTI Products

Combine NTI's video splitters and extenders for complex applications
- 4K DVI/HDMI Video Splitter (VOPEX-DVI4K-2)
  - Supports HDTV resolutions to 1080p when used with the extenders.
- HDMI Quad Screen Splitter/Multiviewer
  (SPLITMUX-HD-4RT)
- DVI-D to HDMI Single Link Interface Cable
  (DVI-HD-xx-MM)
HDMI 2.0 EDID Emulator (HD4K-EDID-EMLTR)

Application Drawings

How to Configure Point-to-Point Connections
Point-to-Many Connections Using an Unmanaged Network Switch

For a point-to-many connection, a standalone network with an unmanaged network switch, hub, or router can be used instead of a managed network switch. It is not recommended to use any other network devices on this standalone network as it may cause a degradation in performance.
HDMI Over IP Extender Screen Shot
Many-to-Many Connections Using a Managed Network Switch

Support for multiple transmitters requires a Managed network switch with VLAN/IGMP support. NOTE: The many-to-many configuration is not compatible with Cisco 2960 switch.

Application Notes

How to Access the Web Interface

After connecting the unit directly to the computer using CATx cable, temporarily set your computer's IP address to 192.168.168.xx to match the unit. Open a web browser and input the unit's factory default IP address: 192.168.168.55 (local) or 192.168.168.56 (remote), into the address bar. Change the IP addresses of the units to match your network's subnet. Revert your computer's network configurations to its original settings. The web interface can now be accessed through the newly assigned IP addresses.

Data Sheet:

Low-Cost HDMI Over IP Extender Data Sheet 307 KB

User Manual:

ST-IPHD-LC - Installation and Operation Manual 471 KB

"MCV has been buying KVM solutions from NTI for many years. They are a trusted and valued vendor. In one situation we ran into an installation in which a KVM was not the right fit. NTI did have a solution that fit what we needed to do - an HDMI over IP Extender. We bought and installed the ST-IPHD-LC in 2013, and on November 1st 2018 it finally failed. MCV is a power plant; we run 24/7/365, so that extender ran every day and every night for 5 plus years without issue. When it failed, we bought two more. It is simple to use and very cost effective. Not only would we buy it again, we did buy it again."

Brandon F

Midland Cogeneration Venture

Midland, MI
"I take care of physical security and electronic surveillance for our corporation. At each building I have at least two computers sitting in wiring closets that send camera feeds to TV monitors in different offices using your ST-IPHD-LC HDMI extenders. I love those!!! I just did an upgrade to the system that if they have a mouse at the office end they can manipulate their camera views."

Terry E

Warsaw Community Schools

Warsaw, IN
"I discovered NTI's ST-IPHD-LC LC HDMI extender by accident when a super important CEO's HDMI extension went bad. Since we never purchased from NTI before, my boss was worried that the unit would fail or be incompatible with the existing setup. But it didn't. Not only that, it outperformed the other vendor's unit in that application! Ever since then, we have been purchasing frequently from NTI. Whenever I can get a product from NTI as opposed to elsewhere, I do."

John R

Xetra Networks

San Diego, CA
"We use the ST-IPHD-LC extenders for digital signage. We set up our PC running the information being broadcasted in a server closet and broadcast to multiple TVs within our customer's facilities. The extenders work very well."

Matt L

ACF Technologies

Asheville, NC

(0)Low-Cost HDMI Over Gigabit IP Extender – Transmitter & Receiver Set

NTI Part #	Description	Qty
ST-IPHD-LC	US NEMA 1-15P
ST-IPHD-LCEU	Europlug CEE 7/16
ST-IPHD-LCUK	UK BS1363
ST-IPHD-LCAU	AS/NZS 3112
ST-IPHD-LCUNV	US NEMA 1-15P with country-specific universal power plug adapter

Collapse all Expand all Related Items :

(0)Low-Cost HDMI Over Gigabit IP Extender – Receiver Only

NTI Part #	Description	Qty
ST-IPHD-R-LC	US NEMA 1-15P
ST-IPHD-R-LCEU	Europlug CEE 7/16
ST-IPHD-R-LCUK	UK BS1363
ST-IPHD-R-LCAU	AS/NZS 3112
ST-IPHD-R-LCUNV	US NEMA 1-15P with country-specific universal power plug adapter

(0)HDMI Male-Male Cables

NTI Part #	Length	Qty
HD-3-MM	3 feet
HD-6-MM	6 feet
HD-10-MM	10 feet
HD-15-MM	15 feet

(0)DVI-D Male to HDMI-A Male Single Link Cable

NTI Part #	Length	Qty
DVI-HD-1M-MM	1 meter
DVI-HD-2M-MM	2 meters
DVI-HD-3M-MM	3 meters
DVI-HD-5M-MM	5 meters

Top Please enter a quantity of at least one product